ask wwgoa | WoodWorkers Guild of America

1 - 24 of 46

Sort by:

Sorry, there were no results

Ask WWGOA: SawStop Power Connections

Question: On SawStop's website, they say that the SawStop cabinet saw must be wired directly into the shop power, according to NEC. As I: 1) like to (must) move my... View Content

Ask WWGOA: Bread Board Ends Pinned

Question: If you are doing breadboard ends on a project that will only be viewed from one side, say perhaps a sofa table or hall table that you never see... View Content

Ask WWGOA: Dust Collection Size

Question: I’m setting up a new shop and I’ve read everything I can get my hands on about dust collection. Now, I’m more confused than I was before doing the... View Content

Ask WWGOA: Using Fallen Wood

Question: In Ontario, Canada, I have free fallen trees cut down by the city to walk away with. How long is too long to consider fallen wood to be not... View Content

Ask WWGOA: Building and Accessorizing a Workbench

Question: This is in reference to the Building and Accessorizing a Workbench video. Very interesting and informative. Why didn’t you drill the bench dog holes with a router and 3/4″... View Content

Ask WWGOA: Breaking Gorilla Glue

Question: Wondering if you know of a way to break apart joints glued with Gorilla Glue. Whoever tried to repair this antique dresser drawer let the glue squeeze out all... View Content

Ask WWGOA: Timber Splitting

Question: How can I prevent my timber from splitting open? We manufacture furniture in South Africa – Cape Town – then transport it to the country as soon as it... View Content

Ask WWGOA: Buffing Compound

Question: Saw your video on finishing wood pens with CA and stick buffing compound. My question is this: what type and brand name is the buffing compound I should use?... View Content

Ask WWGOA: Maple and Cherry Wood

Question: George, you made a pair of Kitchen Tongs, where do you purchase maple or cherry wood 1 1/8″ thick? Submitted by Terry Answer: In my area, Wisconsin, it’s pretty... View Content

Ask WWGOA: Using Barrel Hinges

Question: Regarding your video Using Barrel Hinges, I’ve seen inserts that sit in the hole after drilled, which have points on them to punch a center mark in the opposite... View Content

Ask WWGOA: Drilling Into Masonry

Question: I recently hung two good sized wall cabinets in my garage. I used French cleats for each and they were affixed to brick veneer in the garage. I used... View Content

Ask WWGOA: Environmental Headgear

Question: In his recent woodturning CD George wore an environmental headgear which included a powered air filtration system (You can see it here). Could you let me know the maker... View Content

Ask WWGOA: Cleaning Dried Acrylic Paint

Question: I spray with acrylic paints and sometimes get buildup in spite of constant cleaning. Do you think soaking in mineral spirits will lift dried acrylic better than water? I’ve... View Content

Ask WWGOA: Cutting MDF

Question: What should I use to cut MDF wood? Submitted by Richard W. Answer: This video provides some info on table saw blades. A triple chip blade is best for... View Content

Ask WWGOA: Drying Cut Wood

Question: Simple question maybe. How is the best way to dry wood cut from trees? I have several around the farm here, ranging from Pecan to Oak. During fall we... View Content

Ask WWGOA: Turning Tool Recommendations

Question: I’m new to turning. I bought a Jet 12-20 lathe. I have one full length Easy Wood Rougher. I need to buy more turning tools. Since I’m new and... View Content

Ask WWGOA: Removing Rust from Cast Iron

Question: How do you remove rust from a cast iron surface? Submitted by William M. Answer: I wet sand the surface using WD 40, JB 80 or other rust remover... View Content

Ask WWGOA: Lathe Sharpening

Question: I have loved your lathe videos so much that I have just bought my first lathe. I am getting it set up and know that I need a sharpening... View Content

Ask WWGOA: George’s Solid Wood Storage

Question: George, I have the same system throughout my workshop, garage, and Shed, (from the George’s Solid Wood Storage video) but I put 3/4 ply down for more consistent support.... View Content

Ask WWGOA: Brad Nailer for Light Work

Question: What brand/size/gauge brad nailer would you suggest for light work like that you frequently do in your videos? Submitted by Ross W. Answer: 18-guage and 23-gauge nailers will serve... View Content

Ask WWGOA: Fixing Nail Blowouts

Question: I'm sure that this never happened to you, but... I was nailing on a face frame (I know, I didn't want to use nails but the angles of this... View Content

Ask WWGOA: Joiner Biscuit Sizes

Question: I ordered a Porter Cable biscuit jointer and was wondering what size biscuits to order. How do you determine what size biscuit is used for a particular job. I... View Content

Ask WWGOA: How to Stop Wood from Warping

Question: I built a kitchen for my nephew from the ground up and it didn't turn out too shabby--for a beginner. The top is white hard maple and the rest... View Content

Ask WWGOA: Cure Bandsaw Blade Movement

Question: I just put a new band saw blade (3/8") on my saw. As I was trying to adjust the side bearings, I noticed that the blade moved in and... View Content