4 Table Saw Sleds That Will Improve Accuracy

Table Saw Sleds

Sleds are a very valuable asset. They provide a way to allow the work piece to travel parallel to the blade or cutter head to ensure an accurate cut on both large and small pieces, and even irregular shapes. They can have hold downs, clamps, and/or fences to hold the work piece secure during the cut, preventing the piece from flying off or moving out of parallel with the direction of cut. And most importantly, they help us keep our fingers away from the blade or cutter head. Have we ever had a small piece that needed just a “little cut here”, followed by a potentially stupid move?

So let’s have a discussion about sleds. This article gives you an overview of my four favorite sleds. With a little imagination and ingenuity on your end you’ll be able to adapt those you need for use in your shop.

Table Saw Sleds

Miter Sled

The first one we all think of is the 45-degree miter sled. Mine is similar to the one George made, just bigger and I used oak for the guides. I found it useful to mark the location of the blade area with blue tape as a reminder where NOT to put my fingers.

Table Saw Sleds

Here I’ve added a piece of hard maple as a zero clearance fence.

Table Saw Sleds

This sled came in handy when writing the article Jake’s Tips on Making Miters to make cuts in very small and delicate 1/2” by 3/8” trim pieces on cabinet doors.

Table Saw Sleds

Panel Cutting Sled

The second sled, a panel cutting sled, is invaluable for cutting large pieces, such as plywood case parts and panel doors.

Table Saw Sleds

The fence is located at the top of the sled, perpendicular to the blade. The alternative is to place the fence at the rear of the base, but the size of the panel is then limited by the size of the base. Placing the fence at the top of the base allows for much larger panels to be cut. Note that I made the fence extra long to help stabilize longer panels. Making the panel sled for the left or right side of the blade is a matter of personal preference.

Table Saw Sleds

Crosscut Sled

The third sled is a small version of a very traditional design.

Table Saw Sleds

A cross cut sled can be small, like mine, or cover the entire surface area of a table saw table. It’s designed to give maximum stability and accuracy for any cross cut operation. The sled has a beefy fence at the front and rear edges of the base to keep the base together, since the base has been cut in two to accommodate full travel of the sled through the blade.

Table Saw Sleds

This smaller version was built to hold small pieces of irregular shaped feet for planter boxes.

Table Saw Sleds

As can be seen in this picture, by using the sled the foot can be oriented as needed to insure that the top and bottom are cut square to each other not to mention how secure the piece is and how safe my fingers are when making these cuts.

Table Saw Sleds

Adjustable Box Joint Sled

The problem I have always had with making jigs to cut box joints (finger joints), is readjusting the locator key to loosen or tighten up the fit of the fingers. So I decided to make a sled with two adjustable tables instead of an adjustable key.

Table Saw Sleds

By cutting slotted holes for screws in the base, the key can be moved back and forth to adjust the spacing between the fingers of the joint. I also made the key longer because I was making multiple small boxes out of oak, and wanted to speed up the manufacturing process (I have highlighted the locator key with black marker). As this picture demonstrates, by making the locator key longer, several pieces of wood can be clamped together at one time and cut on the sled. I was cutting up to 10 pieces of 1/4” thick oak at a time with this sled.

Happy sledding

Jake

SawDustbyJake.com

how to buy a table saw guide banner

Share tips, start a discussion or ask one of our experts or other students a question.

Make a comment:
characters remaining

18 Responses to “4 Table Saw Sleds That Will Improve Accuracy”

  1. Jeffrey West

    Setting up shop in garage, but will move to basement shop in the future. Interested in doing mostly small projects, but have a some larger projects in mind.

  2. Mark Levy

    Any plans yet for making a cross cut sled? I see folks have been asking on this thread for years. Any available plans yet? Thanks.

  3. Lawrence Mason

    Are there any actual plans for a good sized sled?

  4. Michael Fullen

    As a premium member, how do I get plans for each of these for sleds? Regards Mike Fullen

  5. THOMAS

    I have a table saw. I am thinking of building a table saw sled, but I have a radial arm saw too, would a sled do much more than the radial saw? TOM Z..

  6. NANCY

    I have an inexpensive Craftman tablesaw. The 2 miter slots are in a removable top on one side of the blade. Do you believe it is possible to build a sled on this type of tablesaw. I'm sure I'd need to make sure that the sled and removeable top is perpendicular to the blade every time I used the sled. Do you see anymore issues? Every time I use a miter gauge to cut I have to adjust it to the blade because of the tabletop being removed and replaced. Thank you for your response.

  7. seidele

    Are there no cut list or plans to DL?

  8. FRANCISZEK

    Hello. I want to build these Jigs but I can't find the plans. I have a premium account and am logged in. Please help. Thank you.

  9. Blanca

    If some one needs expert view on the topic off blogging then i advise him/her to visxit this webpage, Keep up the pleasant job.

  10. Gerald

    do you have any PDF plans for table saw sleds