Balancing Wine Bottle Holder

wine bottle in a wooden holder

Add a whimsical air to your next celebration by placing wine bottles in a seemingly impossible balancing act using these intriguing holders. These special holders support a standard 750-ml bottle of wine in perfect repose, while your guests will stand around it staring in a state of wonder. The trick to maintaining balance is in the angle of the base cut, and the distance from the top hole to the base. This plan will demystify the process and take the guesswork out by providing the measurements that make it work for you.

Click here to download the templates for this project.

spraying adhesive spray on a template

Create template

Start by creating your template. Download and print the supplied pattern, and apply to 1/4″ plywood or tempered hardboard using adhesive spray. Let the spray dry for about a minute before placing it on the template material, which will allow the paper pattern to be removed more easily.

woodworking challenge banner
using a saw to cut around a template on wood

Cut out template

First drill the 1-1/4″ holes as indicated on the template. Then, use either a band saw or scroll saw to cut to the pattern lines, and sand the edges smooth.

tracing wood

Prepare your stock

Any hardwood will work just fine. This is a perfect project to turn end cuts into holiday gifts, as the blank that you will need is only 3/4″x 3″ x 9″.Optionally, for greater stability you can use thicker stock such as 5/4 or 6/4. Trace the cut lines using the template. For better visibility, using a white pencil when using dark wood such as walnut.

drilling a hole into wood

Drill holes

Use a 1-1/4″ bit to drill holes as positioned in the template. The bottom contour could also be cut on the band saw, but given the tight radius we generally do this at the drill press, which provides a quick hole that is consistent in size with the top hole, and leaves a smooth surface that saves on sanding time later.

cutting wood on a band saw

Cut the base angle

Prior to cutting the curved shape on the band saw, cut the base at a 35-degree angle.

cutting with a saw

Cut rough shape on band saw

Using a band saw, cut the curved shapes, leaving the line for final shaping later.

wine bottle in a wooden holder

Test for balance

At this point it is a good idea to test the holder for balance. Before sanding, place a full 750-ml bottle of wine in the holder to see if it stays firmly balanced. You might find that it balances perfectly without further modification. If you are slightly off, it might feel ‘a bit tippy’. If you are grossly off, it won’t stand on its own at all. If it doesn’t balance properly, carefully feel which way the holder is leaning under the weight of the bottle and adjust the angle of the base with ‘tuning cuts’ on band saw as needed, or by lightly sanding with a disc sander. If the bottle leans to the right as shown by the arrow in this photo, decrease the angle of the base cut (try 34-degrees) so that the bottle holder stands more vertically. Sharpen the angle (try 36-degrees) if it leans the other way.

testing wood for balance

Sand to the line

Using a belt sander, carefully sand to the line for final shaping.

using a belt sander to sand a hole

Sand inside holes

Use an oscillating spindle sander or other means to sand inside the holes. After all surfaces have been sanded using power equipment, hand sand to 400-grit to achieve a smooth feel.

hand sanding

Finish

Finish using polyurethane or other durable finish. One way to support small pieces like this as the finish cures between coats is to tap some small finish nails about half way into a piece of scrap wood, leaving a bunch of nails sticking out a small amount at approximately the same height. This will support the piece without much contact surface area, allowing you to finish all sides in a single pass.

Once you get the balancing part down, you can experiment with other fun shapes and designs. If you modify the distance of the hole from the base, you will also have to adjust the angle of the base to establish balance. For example, if the hole is farther from the base, you will need to cut the base at a lesser angle. By experimenting you will find the angle that works for most any design.

Share tips, start a discussion or ask one of our experts or other students a question.

Make a comment:
500 characters remaining

5 Responses to “Balancing Wine Bottle Holder”

  1. Robert Paul Laschon

    Hi Paul, Can I get the plan for this? Thanks a lot. Take care

  2. ben

    thanks Paul for the wine bottle holder plan made first one out of scrap pine, worked perfect. I live in napa valley ca where everybody makes wine (except me). my neighbor makes outstanding wine which I get quite a bit of. thanks to you I can give them a nice gift of a wine bottle holder which they do not have. thanks again for the plan. ben

  3. Len

    Thank you I think it is a wonderful gift idea for friends...Len

  4. christopher

    great fun, worked perfectly, have made at least six and will start to experiment with different shapes, unusual and good gifts

  5. Karey Reese

    Nice quick project when you have some down time between larger projects. I made the template and three bottle holders in about two hours. Nice xmas gifts.