120-Volt vs. 240-Volt in the Wood Shop

different voltage plugs with a question mark

There is a lot of confusion around the pros and cons between 120 volts and 240 volts in the wood shop. The reason for this is that electricity can be a very, very complicated subject! Fortunately, for woodworkers, it doesn’t have to be complicated at all. This article is not about industrial applications, three-phase power, line losses, motor efficiency, or any minute differences between these two options. My intention is only to offer sound, practical advice as it applies to the average home wood shop.

I see lots of different voltage numbers, what’s the deal?

The first thing you need to know is that household voltage in the US and Canada is supplied at about 120/240 volts. These are nominal numbers, and the actual voltage varies somewhat. But, with a few rare exceptions, the electric companies supply high-quality electric power to their customers. For practical purposes, the average woodworker should think of 110, 115, and 120 volts as all being interchangeable. Likewise, think of 220, 230, and 240 volts as being interchangeable. For this article, I refer to 120 volts and 240 volts, but the information applies equally to 110V, 115V, 220V, and 230V motors.

The motors in your shop probably have all sorts of different voltage numbers on them, but it’s not a big deal. Unless something is drastically wrong with either the power available in your shop or the motor itself, then motors that say 110, 115, or 120 volts will all run perfectly fine. Likewise, motors that say 220, 230, or 240 volts should all perform just fine.

motor on a drum sander

This motor on my drum sander is an example of a typical 115V motor. It produces 1-1/2 horsepower, and it draws up to 14 amps.

Which is better, 120V or 240V?

Neither 120 nor 240 is “better” than the other, and neither is more efficient than the other. One might be better for a particular application, but neither is “better.”

To put it simply, there is no practical difference between a motor that is wired for 120 volts and the same motor that is wired for 240 volts. This is fundamental, and it is one of the few things that you need to know about the differences between these two. If you want more detail, the next two sections will help to explain this. If you just want to know how voltage affects you in your wood shop, and you don’t care about the “why,” then skip the next two sections and go right to the bottom line.

If you want more details, read on!

Motors, Volts, Amps, and Power

An electric motor produces “power,” and that power does the “work.” At its most basic level, power is expressed like this:

  • Volts x Amps = Power.
  • So, a 120-volt motor that draws 10 amps will produce 1200 watts of power. Therefore, a 240-volt motor that produces 1200 watts of power will draw 5 amps. (240 x 5 = 1200.)

motor on a Delta belt sander

Some motors, like this one on my Delta belt sander, can run on either 120 or 240 volts. You can see that it produces 1-1/2 horsepower regardless of the voltage that it is wired to run on. You can also see that running it on double the voltage decreases the amperage by exactly 50%.

nameplate on a motor on a table saw

This is the nameplate on the motor in my table saw, and it’s an example of a typical 230V motor. It produces 3 horsepower, and it draws up to 12.8 amps. This particular motor is designed to only run on 230 volts. Hypothetically, a similar 115V motor that produces 3 horsepower would draw up to 25.6 amps.

If 120v isn’t better than 240v, and vice versa, why are there two options?

Great question! It goes back to amperage. It’s also about industry standards and costs. Electric wire is rated for the maximum amperage that it will carry. Larger wires can carry more amps. A 3 hp motor wired for 110 volts might draw 25 amps. That would require relatively large and expensive wires from the breaker box to the receptacle. That same motor wired for 220V would only draw 12.5 amps and could run with smaller and less expensive wires.

A 120V circuit in most American homes are rated at either 15 or 20 amps. Typically, 240-volts is used if a particular load requires more power than a 20-amp, 115-volt circuit can provide. Examples of this would be an electric range or an electric dryer. Other examples of this would be stationary power tools with more than a 1.75 horsepower motor. (Don’t get me started on hand held routers that supposedly produce 3 horsepower!)

The Bottom Line

Whether it’s 120 volts or 240 volts, it’s horsepower that counts. There is no practical benefit to rewiring your 120V contractor saw to run on 240 volts. That will not affect how well it cuts through that nice piece of maple that you’ve been saving.

You can have a great wood shop and do wonderful work without 240V circuits. However, if you think that you might want larger stationary tools and if you have the option, then always include some 240-volt circuits in your wood shop. That’s because larger band saws, cabinet saws, planers, jointers, lathes, and dust collectors have larger motors that require 240V circuits.

It comes down to this: Rewiring your 120V 1.5 hp table saw to 240V won’t give you more oomph at the blade when you’re cutting thick hardwood. However, buying a 240-volt 3 hp saw, equipped with a motor that can’t be practically run on 120v, will give you more oomph.

Share tips, start a discussion or ask one of our experts or other students a question.

Make a comment:
500 characters remaining

29 Responses to “120-Volt vs. 240-Volt in the Wood Shop”

  1. David Cleary

    Read information, I have just called my electrician to have him give me a 240 outlet for my “new” planner. Thanks for the tips

  2. George Burton

    The cost is the same with 120 or 240, volts x amps make watts its the same

  3. Joseph Tripodi

    I approach the issue of 120 vs 240 volts from the supply perspective. My shop has 100 amp service. I have a central Air Conditioner/heat pump and a water heater which have high amp draws when they are running. By wiring my tools to 240 v, when possible, keeps me within the limit of my supply.

  4. Jerry

    There is a definite advantage to 240 volt power. As a motor loads up, the current increases. Ex. 3hp motor will consume approx 2250 watts (746w/hp x 3hp) at max load. Max current at 120v = 18.7a (2250w/120v) and 9.4a (2250w/240v). Motor resistance (R) decreases at max load to about 6.5 ohms (120v/18.7a) and about 24 ohms (240a/9.4a). The resistance of the circuit (wire, circuit breaker, and connection) remains almost constant. Therefore, the circuit resistance becomes a larger percentage of loss to the motor for the 120 volt source. Assume circuit resistance = .5 ohms. Voltage loss at 120v is 9v (18.7a x .5 ohms) and at 240v is 4.7v (9.4a x .5 ohms). Percent voltage loss at 120v is 7.5% ( 9v/120v) and at 240v is 2% (4.7v/240v). I have used my tablesaw in each mode and it definitely has more power at 240v (does not slow down like it did at 120v).

  5. Kevin Stierhoff

    This was a really helpful description for someone who has a small shop with only 110V power at the moment, but with the ability to add 220V circuits as needed.

  6. Mark

    I converted my table saw from 120 to 240 and noticed a significant increase in the acceleration of the table saw motor. This makes sense to me because the initial rate of change in an inductive load such as a motor is directly proportional to the applied voltage. Fundamentally I believe that there is a significant advantage of 240v over 120v.

  7. Lance

    Your comment on "don't get me started on 3 hp routers" shows you may know about volts and amps but not HP. HP is torque X RPM / 5252. so at a given torque, as RPM increases, so does HP. and at 20,000 rpm it only takes .8 lbft of torque to generate 3 HP. The amperage going through the electromagnets creates the strength of the magnetism generating torque. It is very different comparing a 3600 rpm motor to a 20,000rpm one when talking HP. At 3600 rpm it takes almost 5 lbft of torque, more than 5 times what the router has. More torque, more VxA.

  8. Larry Dieffenderfer

    I agree with all you have written. However; I believe (please confirm) evergy consumption is based upon usage on one leg, then doubled . In your high amp 120v tools are on one of the legs (not balanced between the two legs ... which is only by chance) your power usage will be more than it would be if tools were wired for 240v. You are not using more power, you're just paying more for what you are using.

  9. S BRYAN CHAPPELL

    There is one difference you didn't mention. In a cold climate where I live in Regina, Saskatchewan, Canada, my 120 v dust collector would often throw the breaker switch when my shop was cold, say around 50 degrees Fahrenheit. Switching to 220 v solved the problem. After about a year on 220 v and 6 years of use the motor burnt out. At 220 the dust collector did not have more oomph, but it always started without a hitch.

  10. William Spier

    (My website - www.thecarpentershouse.love is under construction, and your field above won't accept the entry apparently unless it's a .com URL.) The big question for me is how do you know when you're buying a 240V, 3HP saw, that can be run on 120V?? Where does the manufacturer make it explicit that a120V power supply will effectively power its 240V unit? I always thought that providing 120V to a 240V motor will decrease the power/efficiency, and you're saying that's not the case?