Upholster a Wrapped Seat Cushion

A customer came into my shop the other day and asked me to replace their uncomfortable and broken fiberglass kitchen stool seats. They wanted to reuse the adjustable chrome bases, but change the seats so they were cushioned and upholstered. I said sure, no problem, and I suggested a simple wrapped padded cushion. The techniques shown in this story will give you the confidence to try an upholstery project of your own.

Here’s how the newly wrapped seat cushions look…

Newly wrapped seat cushions

This is what the seats looked like before!

looked like beforeNow for what I didn’t tell them… I’m just a novice upholsterer! I’ve made some sewn and wrapped seats and cushions for myself, but if there’s “serious” upholstering to be done I contract the work out to a professional. Upholstery is like any skill, the more you learn and practice, the better you get at it. I’ve done enough simple upholstery to be confident that I can get good results, and wrapping cushions like this is a great place for anyone to start learning to upholster.

Upholstery Wrapping Overview

Typically, 1/2″ thick plywood is used for seat frames (platforms) of seat cushions that drop into, or mount on top of chair frames. In this case I used 3/4″ thick plywood because the seats are mounted on pedestal bases and need the added stiffness the 3/4″ plywood provides. This is the same approach you should take if you’re making a seat for a wooden stool base. 1″ dia. vent holes are drilled through the plywood. 1″ thick foam is adhered to the plywood, and 1″ thick Dacron batting is adhered to the foam, and then faux leather (vinyl) is stretched and stapled over the top. The combination of materials gives the seat a thinner, nicely crowned look, which is also comfortable to sit on.

Advanced Upholstering

Moving beyond this simple upholstery wrapping technique can open up an entire world of possibilities. Imagine reupholstering a Queen Anne style sofa! You could go on to learn about folding corners, webbing, sewing, piping, welting, tufting, cambric, fillers, and so much more. All of which you can learn from books (see References), classes at a local trade school, or by contacting a local professional upholstery association to find out what learning resources they might suggest. It never hurts to ask a professional upholsterer too.

Potential Snags

There are a few things you need to be aware of. Using thick fabric can make the work very difficult; it’s hard to wrap, and hard to eliminate creases and puckers. Using very thin fabric is not good either; it’s not durable enough to hold up to the rigors of everyday use. Upholstery grade fabrics are your best choice. It’s never good to wrap fabric over sharp edges; it will wear very fast and then split. It’s best to ease the edges of wooden parts being upholstered to reduce this effect. And the thing you will run into most often… inferior foam, or you choosing the wrong foam for your seats, which I’ve done far too often! Buy your foam from a local upholstery supply house or foam supplier if you can, and give it a “sit test” to feel its compression and comfort. For most seating using medium firm or firm foam works best. Here’s a link to some very good foam cushioning material information: Foam Information And Specifications

Tools Needed:

tools needed

Manual or pneumatic staple gun and 1/4″ long staples.

Band saw or jigsaw.

Drill with a 5/16″ dia. bit and a 1″ dia. spade bit.

Electric kitchen knife. Yes! It’s used to cut the foam, and works better than you would think. Router and 1/8″ roundover bit.

Scissors.

Staple puller.

Trammel point set.

Materials Needed To Make And Wrap These Seat Cushions:

materials Needed

3/4″ thick plywood.

#20 x 1/4″ T-nuts. (for this project. Not always necessary)

#20 x 1/4″ x 3/4″ machine bolts.

3M Foam Fast 74 spray adhesive.

1″ thick medium firm urethane foam.

1″ thick Dacron batting.

Faux leather vinyl.

Cut The Seat Frame Plywood Shape.

cut plywoodUse a jigsaw or band saw to cut out the shapes of the plywood seat frames, and then smooth the sawn edges using a stationary disk or belt sander, or with a hard sanding block. Notice I have the T-nut holes and vent holes laid out. The pedestal bases of this project call for T-nuts. Wood screws could be used to fasten the seats to a wooden base that doesn’t have a cantilever like these stools do, so you could drop T-nuts in that application.

Drill The Vent Holes

drill vent holesUse a 1″ dia. spade bit to drill 4 equally spaced vent holes. The seat foam can retain a lot of air, which needs to be relieved when the seat is sat on. Don’t skip this step. If you did, then sitting on your cushions will be like sitting on a balloon that’s slowly leaking air!

Round Over The Plywood Edges

roundover plywood edgesUse a router and an 1/8″ roundover bit to ease the top and bottom outside edges of the seat plywood pieces.

Trace The Plywood’s Shape To The Foam

trace foam shapeThe foam should be 1″ larger in diameter than the plywood. Use a “Sharpie” marker pen and a spacer to get the correct diameter.

Cut The Foam.

cut foam Use an electric kitchen knife to cut the foam. I bought a cheap one at my local hardware store. Using a knife beats the heck out of trying to cut this stuff with scissors! Be very precise when you cut the shape. Any sloppiness here will show in the final wrapped seat. A word of caution; don’t be tempted to cut the foam on a bandsaw, that would be very dangerous.

Trace the shape of the foam to the Dacron and cut it out using a scissors. Again, be precise with the cutting. Cut the vinyl 8″ larger in diameter than the plywood.

Adhere The Foam To The Plywood, And Then The Dacron To The Foam.

adhere foamThere are a lot of spray adhesives available, but in my option 3M Foam Fast #74 is the best there is for adhering foam. It makes the work fast and sure; others are more work. Coat both surfaces and then join the pieces. Use it to adhere the Dacron to the foam too. Make sure the T-nut side of the plywood is up so the foam is placed on top them.

Watch This Video Of Wrapping This Seat, And Also Wrapping A Square Corner.

Trim Away The Excess Fabric.

trim with scissorsUse a scissors to trim away the excess fabric. I needed to add more staples along the trimmed edge so the little ridge of buckling didn’t show when the cushions were mounted to their bases.

References

Here’s a great online site with a lot of useful information:

Professional Upholstery & Soft Furnishings Group

Books I find useful:

Beginners’ Upholstery Techniques by David James

Matthew Haly’s Book of Upholstery

Singer Upholstery Basics Plus by Steve Cone

Sources

1/4″ 3-Prong T-Nuts (#20), 8-Pack, item #47583

Rockler

www.rockler.com (800) 279-4441

3M Foam Fast 74 Spray Adhesive Orange, 16.9 oz. Aerosol Can

Amazon.com

www.amazon.com

Upholstery Supplies and Tools

We Sell Upholstery Supplies Online (800) 262-5790

Share tips, start a discussion or ask one of our experts or other students a question.

Make a comment:
500 characters remaining

4 Responses to “Upholster a Wrapped Seat Cushion”

  1. BC

    Well done. Nice to see the right way to do it. I have done them before and they all look different. That is because I had never seen the right technique to do it

  2. Dan Montag

    May I suggest using hex drive screw in threaded wood inserts in the place of t-nuts. T-nuts can come out inside your upholstery job and ruin your day if you don't have more vinyl. This usually happens if the threads on the bolt or machine screw is damaged and you wind up pushing too hard and the t-nut pops out of the wood. Threaded inserts are put in from the out side and could be replaced ,if need be, from outside your upholstery job. Inserts are better all around.

  3. Mike

    Thanks. Great, informative information.

  4. jivod60

    This is very informative. I have not tried upholstering before, but this gives me some ideas!